Have you decided to find out how to install a trolling motor and start to make positive
changes in your approach to recreational fishing activities? You have to become skilled at
the basics of the trolling motor at first and take note of professional guidelines to successfully install
a trolling motor on your boat.
As a self-contained unit, a trolling motor includes an array of important elements like propeller,
controls and an electric motor. This trolling motor is affixed to a boat at the stern
or bow. A gasoline-powered outboard used in this trolling may also be called as a trolling motor.
This motor is usually lifted from the water for reduced drag while the primary engine of the boat
is in operation.
Three options for installing a trolling motor
An electric trolling motor for pontoon boats was invented by O.G. Schmidt in 1934. This
trolling motor is designed to let fishermen maneuver boats at the slowest possible speed than
trolling speed with the motor in the outboard which has the maximum control when compared to
paddle or oars. A trolling motor is appropriate for both saltwater and freshwater fishing. This
motor can be mounted in one of the following three places.
On the transom (stern)
On the bow
On the engine itself
Do you wish to silently maneuver your boat while pursuing fish? Mounting the trolling motor
before the boat is a common option at this time. If you are eager to try this approach, then you
have to remember that the mounting plate must be in the position to run horizontal to the water
for proper functions of the trolling motor.
You may require placing something underneath the mounting plate’s front side to install the
trolling motor on the slanted bow in the boat and ensure that it is horizontal to the water. V-
shaped aluminum is preferred and suggested by regular users of the trolling motor. This is
because this material is designed to be bent in a proper way and correct the height.
Do not get confused about which side it must go on while mounting the trolling motor to the
boat’s bow. Many casters experience and ensure about overall benefits of operating the trolling
motor with their opposite foot throughout casting. You can experiment the trolling motor
mounted on both sides and identify which setup works best as per your requirements.
As a teenager or an adult with a desire to get relaxed by a day out on the water, you can focus on
guidelines for enhancing your recreational fishing activities. There are loads of common things
for interrupting people fishing for enjoyment. Some of these things are noise and commotion.
Once you have geared up for silent and enjoyable fishing, you can buy and install the trolling
motor. This exclusive motor is designed to give an appropriate way to seamlessly glide the boat
through the water devoid of a fuss. Every user of this trolling motor can make certain that they
can keep the water still and calm as expected.
Installing the trolling motor on the transom
It is the right time to find out and follow the hassle-free way to install the trolling motor. You
can focus on how to install the trolling motor on the transom at first.
Open the mounting bracket clamps
Slip the motor over the transom
Tighten the clamps
One or two clamps in the transom-mounted trolling motor are assembled into the mounting range
for holding the motor in position. These get open when users turn the clamps to the left that is
counterclockwise. Do not forget to place the trolling motor close to the stern’s center without
interfering the main motor’s operation. The top of the stern is used to flush the top of the
mounting bracket.
If you have done it, then you have to tighten the clamps by turning them clockwise. This trolling
motor has to be positioned in a way to let the motor section’s center is at least 22.5cm
underwater while the motor is running. This is because this position is used to keep the propeller
from breaking the surface of the water and produce the noise used to spook fish.
Installing the trolling motor on the engine
The first step to install the trolling motor on the engine of the boat is to place the mounting
bracket on the top of the anti-cavitation plate of the engine with the motor up. The mounting
bracket is used to keep the trolling moor breaking the surface of the water when the boat is on
the plane. This anti-cavitation plate is located above the propeller on the outboard unit of the
motor of an inboard-outboard type or outboard motor.
The next step is to make holes through the anti-cavitation plate. Drill holes for the mounting
bolts. You can place the mounting bracket on the anti-cavitation plate’s top again. The last step is
to insert the mounting bolts and tighten such bolts.
Installing the trolling motor on the bow
Are you willing to find out how to successfully install the trolling motor on the bow? You can
focus on the following guidelines and make an informed decision to install the trolling motor.
Separate the assembly of the trolling motor from the mount base
Identify a suitable place on the deck to attach the base
Drill the holes into the deck
Drill the holes for the mounting bolts
Thread a bolt via every hole of the mount base
Slip a rubber washer onto all bolts below the mount base
Place the base over the drilled holes
Slip the bolts through all holes
Make certain that the rest level of the base is against the surface of the deck
Thread a steel washer and retain nut onto all bolts
Secure the assembly of the motor to the base
Conclusion
Did you enjoy this tutorial about installing your trolling motor and ready to follow this smart
approach hereafter to get the desired result? You can prefer, buy and install a trolling motor for
enhancing your recreational fishing activities hereafter. Proper installation of the trolling motor
is very important to get the most out of this product. You will get the most expected result when
you double-check how to install trolling motor on time and use this trolling motor in an efficient
way. For detail recommendation about the trolling motor please check out this article on
https://www.outdoorgearworld.com/boating/
